ScreedPerl for lightweight, insulating screeds
High quality screeds that offer the following advantages:
- Insulation – Roughly 9 times the insulating properties of ordinary screeds,
saving significantly on heating and cooling costs
- Lightweight – weighs approximately 25% of traditional screed materials
- Allows for a suitable slope and water run-off on roofs
- Fire protection for up to 4 hours
- Ease of use – just add water
- Inorganic, non-toxic and environmentally-friendly
Perlite possesses millions of tiny, glass-like air particles that act as insulation cavities that reduce heat transmission. A significantly higher R-value saves on heating and cooling costs. The thermal conductivity (K-value) of ScreedPerl is 0.1046 W/m·K*.
The thermal resistance or “R-values” for ScreedPerl is therefore:
The thermal conductivity of traditional cement and sand screeds is between 0.72 W/m·K and 1.13 W/m·K. Taking the medium of 0.93W/m·K, the “R-values” for traditional cement and sand screeds are:
ScreedPerl therefore provides roughly 9 times the insulation of ordinary screeds.
The loose bulk density of ScreedPerl
= 360 – 370kg per m3
The installed weight of ScreedPerl = 460 – 470kg per m3
The installed weight of screeds using traditional materials = 2000 – 2200kg per m3
- ScreedPerl is non-combustible and releases no smoke or toxic gas
- ScreedPerl does not disintegrate or spall when cooled suddenly with a firehose
- ScreedPerl offers excellent fire protection for up to 4 hours. It has low linear expansion characteristics which greatly reduce the development of cracks, ensuring that the temperature of the structure and load bearing members is maintained below the critical point at which weakening or failure is likely to occur.
Superior acoustic insulation
Enhances sound absorption through walls
Dampens noise, particularly pulsed sounds
ScreedPerl is a recyclable, inorganic volcanic mineral offering excellent thermal insulation properties and energy savings.
Particularly advantageous in green building applications for its energy-efficient properties.
Does not rot or decay.
Can withstand normal wear and tear.
Successfully used around the world in construction since 1946.
ScreedPerl is installed in a similar way to ordinary screeds. Perlite particles, however, are more fragile than conventional aggregates and care should be taken to prevent pulverising the particles which will lead to performance loss.
High Return on Investment
A small investment in ScreedPerl during the design and construction phase will provide significantly improved thermal insulation properties and ultimately enormous savings in heating and cooling over the life of the building.
ScreedPerl can be applied to flat, uneven or curved surfaces.
Reduced construction costs
ScreedPerl reduces the demand for structural steel or other support structures.
Slope to drain
Standing water on a roof deck is destructive to roofing membranes and often results in leaks.
ScreedPerl can easily be sloped towards drainage points or to the roof edge.
Once placed, it is simply screeded to the desired thickness and slope.
ScreedPerl roof decks are seamless and provide a monolithic base for roofing that is smooth and even.
Roofing membranes can also be adhered directly to the ScreedPerl using standard fasteners.
Roofing can be applied as soon as the ScreedPerl can take traffic and is sufficiently set to adhere to hot asphalt or bitumen. Under normal conditions, this is about three days. Timing will vary according to weather conditions.
How to screed a floor or roof
These instructions are to be used as a guide only as this is not the only bonded screed method in use. Before starting, please ensure that you wear suitable protective clothing, boots, gloves and safety glasses.
CemteQ has a fully equipped laboratory and works closely with a number of leading concrete technology partners as well as AfriSam to develop and test products. We also provide on-site practical training on the application of our products.
Mass per bag12,5kg
Coverage per bag1 bag = approximately 0,9m2 at 30mm thick
Bulk Density Loose = 360 - 370kg per m3
In-situ = 460 - 470kg per m3
ISO compressive strengthTypically between 2MPa and 3MPa at 28 days dependent on water content.
Application temperature Between +8ºC to +35ºC.